AK-UCU500PSJ AK-UCU500ESJ

AK-UCU500PSJ AK-UCU500ESJ

SKU: ACC-SW-AK-UCU500 Kategorie: ,

Opis

The CCU Supports both 4K and HD Formats by just Changing the Camera Head.
It Enables a High-quality, Long-distance Optical Fiber Transmission Camera System to be Configured at a Reduced Cost.

  • Optical fiber transmission of uncompressed video signals over a distance of approx. 2,000 m between camera and CCU*.
  • The compact, lightweight unit measures 2U in height and is rack-mountable.
  • Supports IP streaming (100 Base-T).
  • An SD memory card can be used for saving user files and updating firmware versions.
  • * When power is supplied from CCU.

Supported Formats

4K (3G-SDI x 4)*1 3840 x 2160/59.94p, 50p, 29.97p, 25p, 23.98p
HD (3G-SDI) 1080/59.94p, 50p, 59.94i, 50i, 23.98p over 59.94i, 29.97PsF, 25PsF, 23.98PsF, 720/59.94p, 50p
HD High Speed
(3G-SDI x 4)*2		 1080/239.76p, 200p
SD 480/59.94i, 576/50i
  • *1: When AK-UC3000 4K Studio Handy Camera is connected.
  • *2: When AK-HC5000 HD Studio Handy Camera is connected.

Input / Output

4K MODE*1 SDI OUT x 4 (4K), SDI OUT x 3, SDI OUT (PM) x 1, VBS x 1,
VBS (PM) x 1
HS MODE*2 SDI OUT x 4 (HS), SDI OUT x 3, SDI OUT (PM) x 1, VBS x 1, VBS (PM) x 1

SDI OUT x 7, SDI OUT (PM) x 1, VBS x 1, etc.
RET Input (SDI: 4ch, VBS: 1ch) etc.
LAN-TRUNK output
PROMPT Input (SDI : 1ch, ANALOG : 2ch)

  • *1: When AK-UC3000 4K Studio Handy Camera is connected.
  • *2: When AK-HC5000 HD Studio Handy Camera is connected.

Rear View

Specifications

Power Supply AK-UCU500P/AK-UCU500PS 100 V – 120 V AC, 50 Hz/60 Hz
AK-UCU500E/AK-UCU500ES 100 V – 240 V AC, 50 Hz/60 Hz
Power Consumption 500 W (Without camera connected: 70 W)
Capacity for Supplying Power to a Camera 240 V AC (tolerance: 5%), 1.46 A , 50 Hz/60 Hz
Operating Temperature 0 ℃ to 40 ℃ (32 °F to 104 °F)
Humidity 10 % to 90 % (no condensation)
Weight Approx. 8.8 kg (19.4 lb)
Dimensions (W x H x D) 424 mm x 88 mm x 401 mm (16-5/8 inches x 3-7/16 inches x 15-13/16 inches)
(excluding protrusions)
Video Output 3G/HD/SD-SDI 7 lines (embedded audio is supported only for HD signals)
HD/SD-SDI 1 line (shared with picture monitor output*1; embedded
audio is supported only for HD signals)
Analog composite 2 lines (1 line shared with picture monitor output*1)
HD TRUNK Output HD-SDI 1 line (cannot be used in UHD/HS mode)
Return Input 3G-HD/HD/SD-SDI 4 lines (RET1 input has active-through output)
Analog composite 1 lines
Prompter Input HD-SDI 1 line (with active-through output)
Analog composite 2 lines (through output of 1 and input of 2 share the connector*1)
It is not terminated when the unit is turned OFF. No through output
Reference Input BB (black burst) / tri-level*2: 1 line
(automatic termination, connect to upper connector; BB signal and tri-level signal automatically recognized, with loop-through output)
Microphone Output 0 dBm/600 Ω, 2 lines (XLR, 3-pin, male)
Communication Intercom input/output (ENG / PROD, 0 dBm, 600 Ω (4 W) / 1 V [p-p], 200 Ω (RTS), 4 W / RTS / CLRCOM): 2 lines*1
PGM input (0 dBm/600 Ω) : 2 lines
Tally input (red, green, yellow) : 1 input each
AUX WFM control
6-bit (open collector output, terminal shared with camera microphone gain setting*1)
Camera microphone gain setting input
5-bit (photo-coupler input, terminal shared with WFM control*1)
Down-conversion system setting input 2-bit (photo-coupler input)
TRUNK RS-422 / RS-232C
2 lines*1
FRONT ROP RS-422
1 line, 16 V DC output (only one of this and REAR ROP can be selected at one time via the menu
or the [ROP FRONT/REAR] selection switch on the front panel)
REAR ROP RS-422
1 line, 16 V DC output (only one of this and FRONT ROP can be selected at one time via the menu
or the [ROP FRONT/REAR] selection switch on the front panel)
MSU RS-422
1 line, GPI for control
LAN TRUNK LAN connection with camera side via an optical cable*3
1 line, 100BASE-T, 1000BASE-T
LAN Personal computer connection for distribution via the Web*3
1 line, 10BASE-T, 100BASE-TX (use a crossover cable when connecting directly with a personal computer)
  • *1: Depending on the setting, only one of them can be selected at one time.
  • *2: The BB (black burst) signal and tri-level sync signal of the reference input are recognized automatically.
  • *3: IP video cannot be transmitted when [CCU MODE] is set to [2160/23.98p], [2160/23.98PsF], [1080/23.98p], or [1080/23.98PsF].

Related Products